In my last post, outlined some ideas and goals for talking the slop out of the fit between the upper and lower receivers on the AR-MPR rifle. The first step is to remove the gaps between the sides of the upper receiver lugs, and the channels at the front and back of the lower receiver. […]
A while back, I posted some AR-MPR rifle accurizing plans. This was my first-pass at enhancing the accuracy of the AR-MPR rifle. Since this post, I have had a few range visits (sorry, don’t have photos as the range does not permit photography) where I did not see the kind of accuracy and consistency that […]
For a while I have been wondering about the RCBS Rifle Bullet Feeder – and now that I’ve setup and used the 22 caliber kit on the RCBS Pro-2000, I know a lot more about how this tool works, and what it is capable of. Setting up the unit is fairly straightforward, with a requirement […]
Continuing with our coverage of high-volume loading of .223 Remington and 5.56 NATO ammunition for the AR-MPR project, this time we’ll look at using the Hornady Lock-N-Load AP to load for the AR-15. In this video, I’ll show loading in full progressive mode with the use of the Hornady Lock-N-Load Case Feeder system as well. […]
If you have an AR-15, you know that they tend to chew through ammo very quickly. It’s a lot of fun, but it also gets expensive really quickly, especially if you are requiring match-grade ammunition. The solution is to load .223/5.56 on a progressive reloading press. If you really want to crank it up, you […]
Recently, I gave a quick overview of the RCBS Rifle Bullet Feed System. In that post, I gave an overview of what’s included in the kit. In this post, we’ll take a look at what this system looks like installed on a 5-Station reloading press (The RCBS Pro-2000 in this case). As you can see […]
Phase III of the AR-MPR AR-15 rifle project is really all about “precision mass production” of the ammunition that we’re developing in Phase II (precision single stage loading). There are a couple key things that we’ll explore: first, we’ll look at progressive reloading of .223 / 5.56 ammunition. We’ll also extend our production rates by […]
If you are a precision shooter, you care about consistency for the cartridges that you shoot. One of the most important factors to measure and control when reloading match ammunition is bullet concentricity. Simply stated, this is the alignment of the case and bullet. If you have “good concentricity”, you will have the axis of […]
In this video, we’ll use the Hornady OAL Gage measurements from our first Phase II loading video: AR-MPR: Phase II – Determining Max COL with OAL Gage and measure the dimensions of the cartridge and magazine to determine the optimal bullet seating depth for the bullet and rifle in question. We’ll then use the Redding […]
For AR-MPR, I’m chasing a .5 – .75 MOA accuracy goal. Initially, I started with 3-shot groups when I function tested the rifle, but have upgraded the challenge to “consistent 5-shot groups at .5 – .75 MOA”. In order to track my progress, I’ve taken a hint from Paul over at http://accurateshooter.com – use the […]
One of the important aspects of a precision rifle is the overall rigidity of the entire rifle – the action, barrel, stock, and other components – the entire unit must be solid in order to shoot with maximum precision. The AR-MPR rifle was initially put together with an M4-Style 6 position collapsible stock. This imposed […]
In this video we’ll continue the precision loading process by using the Redding 3-BR powder measure and the Hornady Auto Charge to dispense powder loads. Next, we’ll cover calculating optimal seating depth, and seating the bullets. Thanks, Gavin http://ultimatereloader.com/wp-content/uploads/2010/11/AR-MPR-logo-wide-small.jpg
I just read a great article written by Robert Whitley of www.6mmar.com fame that was posted on the http://accurateshooter.com blog: What Makes an AR Accurate — Whitley Offers Answers Talk about good timing! This post helped me plan the first wave of accurizing activities for the AR-MPR rifle. My goal is to remove any factors […]
In this video we’ll start the precision loading process by lubing, sizing, depriming, and priming cases. We’ll walk through the features of the Redding Big Boss II, show how to lube .223 cases, validate sizing die setup, and then size/deprime/prime the cases. Next, we’ll cover charging the cases with the Redding 3-BR benchrest powder measure […]
One of the important things to know before loading rifle ammunition is how far out (shallow) you can seat bullets, and what the optimized seating depth is for a particular bullet for your rifle and shooting application. For AR-MPR Phase II, we’re going for maximum accuracy, and also need to assure proper feed characteristics so […]
In my last post, I gave an overview of some of the Redding equipment that we’ll be showcasing during Phase II of the AR-MPR project. I this post, I’ll cover some Hornady equipment that will also be used for this precision loading phase of the AR-MPR project. We’ll cover more Hornady gear (such as the […]
