300 PRC Initial Load Development: 225 grain ELD-M and Ramshot Magnum

Yes it’s tedious, and yet it takes a lot of time, but I really enjoy load development! And this time with 300 PRC, I’ll have two nearly identical barrels to perform load development  with. Both are match-grade barrels from Benchmark! One will be 1:9.5 twist (the custom 300 PRC used in this article), and the other will be 1:8.5 twist, as a part of my Remington 700 Long Range re-barrel job (stay tuned!). This time I’ll also cover something a bit different- working up a load when you don’t have complete load data. Let’s get to it!

Disclaimer

Ultimate Reloader LLC / Making with Metal Disclaimer: (by reading this article and/or watching video content you accept these terms)

  • The content on this website (including videos, articles, ammunition reloading data, technical articles, gunsmithing and other information) is for demonstration purposes only.
  • Do not attempt any of the processes or procedures shown or described on this website.
  • All gunsmithing procedures should be carried out by a qualified and licensed gunsmith at their own risk.
  • Do not attempt to repair or modify any firearms based on information on this website
  • Ultimate Reloader, LLC and Making With Metal can not be held liable for property or personal damage due to viewers/readers of this website performing activities, procedures, techniques, or practices described in whole or part on this website.
  • By accepting these terms, you agree that you alone are solely responsible for your own safety and property as it pertains to activities, procedures, techniques, or practices described in whole or part on this website.

Components

For this load development exercise, I used the following components:

  1. Hornady 300 PRC new cases (un-primed)
  2. Hornady 225 grain 30 caliber ELD-M bullets
  3. Ramshot Magnum powder
  4. Federal 215 Large Rifle Magnum primers

Interpolating Load Data: Enter At Your Own Risk

So what do you do if you have a powder or other component that you’d like to use, but don’t have load data for it? In that situation it’s usually best to get as much data as you can, and interpret/interpolate for the components you’re using. I could not find 300 PRC load data for Ramshot Magnum powder, but I did find enough data to safely work up a load!

First, I took a look at Hornady’s published load data for 300 PRC. I knew I was going to start with Hornady’s 225 grain ELD-M bullet since I wanted to compare performance with the Hornady Match ammunition I used during barrel break-in.

Here’s a snippet from Hornady’s load data: (for reference only, always get latest data form HERE).

I knew that H1000 was a good powder for cartridges like 300 PRC, and Retumbo as well, so I focused on those data points from Hornady’s published load data. The second task was to look at those powders on Hodgdon’s relative burn rate chart:

Aha! Ramshot Magnum falls right between H1000 and Retumbo. Very convenient! So my strategy was to put the max load charge weight right between the max charge weights for H1000 (77.5 grains) and Retumbo (78.9 grains). I assumed Ramshot Magnum would have a max charge weight around 78.2 grains or so. This is not fool-proof since I’m assuming similar densities for the three powders. Hence starting on the low side and working up to the calculated/interpolated max charge. I’ll cover that next!

10-Shot Satterlee-Style Test

As I covered in a more in-depth article:

Expanded 10-Shot Load Development for 6.5 Creedmoor

It’s very useful to run this Satterlee-style testing when working up a load, some times as a very first step for each trial run with new components (like trying a new powder or bullet). So that’s where I started with this 300 PRC load. During this testing, I was able to monitor pressures while shooting the string in my “uncharted territory” 300 PRC load development with Ramshot powder. That’s like hitting two birds with one stone!

For this 10-shot load development test pass, I started just beyond my calculated max (do this at your own risk) and worked back over 10 charges subtracting 0.5 grains for each powder charge. I loaded up the rounds (more on that in a future article), and shot them over a Magnetospeed V3 chronograph which produced the following data:

225 ELD-M Ramshot Magnum 10-shot ladder
Powder Charge Shot Speed
74.00 1.000 2619 ft/s
74.50 2.000 2646 ft/s
75.00 3.000 2670 ft/s
75.50 4.000 2661 ft/s
76.00 5.000 2716 ft/s
76.50 6.000 2717 ft/s
77.00 7.000 2757 ft/s
77.50 8.000 2803 ft/s
78.00 9.000 2792 ft/s
78.50 10.000 2819 ft/s

 

This is not the “most clean” graph I’ve produced from this 10 shot load development since the “nodes” were not pronounced near the max charge. So I had to make some educated guesses moving from 10-shot over to Optimal Charge Weight (OCW). The good news was, no pressure signs whatsoever!

Optimal Charge Weight Tests

After performing a 10-shot load development test, I’ll typically take “speed nodes” (See the main article) and shoot some groups “around the nodes”. Since I didn’t have “super-clear” nodes on my 10-shot load development graph, I decided to shoot 5-shot groups (as seen in the video) up towards the max charge weight, again incrementing by 0.5 grains for each test. Here’s the results in table form:

Group Charge Weight Group Size SD
Group 1: 77.500 grains 1.300 inches 15 fps
Group 2: 78.000 grains 1.100 inches 18 fps
Group 3: 78.500 grains 0.606 inches 5 fps
Group 4: 78.600 grains 0.540 inches 11 fps

At 78.5 and 78.6 grains I had good results. I did not get super-consistent SD numbers for velocity and I believe that’s because of barrel heat fluctuations during testing. I’m planning to start monitoring barrel temperature for these tests with temperature strips or a non-contact thermometer so that I can take that “variable out of the equation”.

The best group came in a 0.540″ (I had another that was very close to this) which is 0.515 MOA. Now I’m really getting close to my “consistent 0.5 MOA” goal for this cartridge, very exciting!

Next steps for 300 PRC load development include:

  1. Varying bullet seating depth
  2. Testing additional bullets
  3. Testing additional powders
  4. Testing with 2nd 300 PRC rifle (following that build)

I’m having so much fun with this project, and I hope you all are enjoying it too! Don’t miss out on Ultimate Reloader updates, make sure you’re subscribed!

Thanks,
Gavin

3 thoughts on “300 PRC Initial Load Development: 225 grain ELD-M and Ramshot Magnum”

Leave a Reply to John Murdoch Cancel reply

Your email address will not be published. Required fields are marked *

For Commerical Inquiries:
Ulitmate Reloader Commercial Services



Reloading Safety

Polls