We’ve spent a lot of time behind TriggerTech single-stage triggers here at Ultimate Reloader. Kyle Shields and I put together a complete breakdown of their Remington 700 lineup, from the new Primary to the flagship Diamond, with in-depth analysis on our TriggerScan TS-11.
Disclaimer
Ultimate Reloader LLC / Making with Metal Disclaimer: (by reading this article and/or watching video content you accept these terms). The content on this website (including videos, articles, ammunition reloading data, technical articles, gunsmithing and other information) is for demonstration purposes only. Do not attempt any of the processes or procedures shown or described on this website. All gunsmithing procedures should be carried out by a qualified and licensed gunsmith at their own risk. Do not attempt to repair or modify any firearms based on information on this website. Articles on this website are derived from original video content and may utilize artificial intelligence (AI) tools for initial drafting, transcript processing, and editorial refinement; no AI technology independently generates or verifies technical instructions or safety data. Ultimate Reloader, LLC and Making With Metal can not be held liable for property or personal damage due to viewers/readers of this website performing activities, procedures, techniques, or practices described in whole or part on this website. By accepting these terms, you agree that you alone are solely responsible for your own safety and property as it pertains to activities, procedures, techniques, or practices described in whole or part on this website.
About TriggerTech Triggers
We’re huge fans of TriggerTech. The Zero Creep technology, easy install, packaging and quality are all amazing. If you’re trying to decide which Remington 700 single-stage trigger to buy, this is one place to check them all out.
What makes these triggers special is TriggerTech’s patented mechanism, with a free-floating roller between the trigger and the sear. It eliminates the sliding friction you get when two surfaces have to slide past each other to break the sear, and it gives TriggerTech triggers their zero creep action. The designs vary a little, but that roller is at the heart of all of them.
TriggerScan Testing
The TriggerScan TS-11 uses a motorized actuator that moves through distance increments and takes a force reading at each, producing a very smooth force-distance graph. It’s essentially a laboratory instrument. At SHOT Show one year at the Dvorak Instruments booth, I watched someone tap the frame of a revolver mid-scan, and you could see the slight ripples in the graph.
For each adjustable trigger, Kyle ran three scans at the minimum, medium and maximum settings to check consistency. The key is resetting the rifle to the exact same position every time. Each trigger had 66 clicks of adjustment, so medium was about 33 clicks.
To set the minimum for testing, Kyle backed the set screw all the way out, then clicked it back in about three clicks. He safety-tested each trigger at that setting to make sure it wouldn’t slam fire, but we didn’t do drop testing. If you’re running a trigger at its minimum in a real rifle, you’ll definitely want to test it thoroughly.
Results can vary from factory specs because of dimensional variances in the cocking piece, the bolt and so on, but they give you a great picture of each trigger’s pull quality.
TriggerTech Primary
The Primary is the newest model and the most affordable. We tested it in the [VERIFY: Bergara rifle model] in 300 PRC we recently reviewed, a lightweight full magnum premium rifle.
- Single-stage, left or right safety
- Pull weight: 1.5 to 3.5 lb
- Typical use: hunting
- Shoe options: traditional curved, straight flat, PVD black curved, PVD black flat
- MSRP: $174.99 (PVD: $184.99)
The Primary comes in the same premium branded case as TriggerTech’s other triggers, and the left or right safety option should make the lefties happy. On the TriggerScan, it showed extremely consistent results and a really nice pull: 1.8 pounds at minimum, 3.1 pounds at medium and 4.8 pounds at maximum.
At about $175 to $185, I think the Primary is a great buy if you’re okay with a 1.5-pound minimum, and for most people, it is. Especially coming from a gritty factory trigger, it’s a huge upgrade.
All of these triggers also have a bottom-facing adjustment screw, which can’t be understated if you adjust your triggers often. A lot of new chassis have a slot for your Allen key. Otherwise, one trick is to drill a hole in the trigger guard right under the adjustment screw. I’ve done that several times for quick adjustments on the TriggerScan or in the field.
TriggerTech Special
The Special is a very popular trigger and the all-rounder of the lineup. Its 1-pound minimum gets it down to my maximum for a hunting rifle. If it’s a rifle I’m very familiar with, I’ll go under that, but I wouldn’t suggest it for anyone who isn’t very familiar with their rifle. It all comes down to trigger discipline and safety testing.
- Single-stage, left or right safety
- Pull weight: 1 to 3.5 lb
- Typical use: hunting, competition and F-Class
- Shoe options: traditional curved, straight flat, PVD black curved, PVD black flat, PVD black Pro Curved
- MSRP: $234.99 to $244.99 (depending on PVD)
We tested the Special in our Stiller Predator, originally built as a 22 Creedmoor. We also used a Special set at 1 pound in our 224 Valkyrie bolt-action build. With 70-grain RDFs, that rifle shot several quarter-inch groups over the years, and the trigger definitely enabled that.
The TriggerScan showed a very consistent, smooth, grit-free pull: 0.9 pounds at minimum, 1.8 pounds at medium and 3.5 pounds at maximum.
Here’s a tip: some OEMs make the trigger hanger pin holes undersized, which makes installation a pain. If you run an oiled [VERIFY: 0.125″] straight-flute reamer through the holes with a drill, the install can go a lot easier. Kyle was able to push the pins right through with a punch on this one.
TriggerTech Rough Diamond
The Rough Diamond is a specialty version of the Diamond. It’s a very robust, tough trigger built specifically for Remington 700 clone actions, so it’s a great option for PRS shooters or anyone wanting increased durability. Note that it’s for clone actions only, since it doesn’t support the traditional Remington 700 bolt stop mechanism. Bergara actions qualify, with their external bolt release.
- Single-stage, left or right safety
- Pull weight: 8 to 40 oz
- Typical use: general precision, competition and F-Class
- Lever options: PVD black Pro Curved, PVD black flat
- MSRP: $309.99
I usually run target triggers at about 6 to 8 ounces, so the 8-ounce minimum is right there. On the TriggerScan, the Rough Diamond measured 8 ounces at minimum, exactly to spec, 15 ounces at medium and 43 ounces at maximum. Interestingly, it showed a very straight, linear force build before the break, which we didn’t see on the other triggers. That makes it very predictable.
For a top-tier trigger, the Rough Diamond is a great all-rounder thanks to its robustness and clone compatibility. I want to spend more time with it doing long-range and target shooting.
TriggerTech Diamond
The Diamond is the flagship. It also has a removable safety, which matters for an upcoming ELR build where the action has no cut for the safety lever.
- Single-stage, left or right safety (removable)
- Pull weight: 4 to 32 oz
- Typical use: benchrest, competition and F-Class (I’d add ELR)
- Lever options: PVD black Pro Curved, PVD black curved, PVD black flat
- MSRP: $334.99
Like the Rough Diamond, it’s for clone actions only. If you go down to 4 ounces, be careful and do a bunch of testing, since there can be issues depending on the geometry of the cocking piece.
The TriggerScan looked similar to the Rough Diamond, though not quite as linear at lower pull weights. It measured 5 ounces at minimum, very close to the advertised 4 ounces, 8 ounces at medium and 32.5 ounces at maximum.
The Diamond is my preferred trigger. I’ve probably spent more time behind it than any other trigger. Almost everyone who shoots one of my rifles is shocked at how light it is, but it’s so predictable. I know exactly when the sear is going to break, and that’s the most important thing to me.
It’s one of the best upgrades you can make to your rifle. When we took the CVA Endura muzzleloader out to 706 yards, I put a 50-power scope and a Remington 700 Diamond on it, since it shares the same trigger hanger as Bergara actions. That definitely elevated things and helped me get my group size down.
Conclusion
Whatever your application, TriggerTech has you covered across price, features and pull weight. Kyle’s favorites are the Diamond and Rough Diamond, but he’d take any of them. All of the Ultimate Reloader custom rifles we’ve sold to the public, including our 6.5 Creedmoor and 223 trainer builds, used Remington 700 Diamonds. That’s the level of confidence we have in TriggerTech.
Kyle also just finished testing TriggerTech AR-15 triggers, and we shoot a lot of TriggerTech two-stage triggers, so watch for those stories.
Get the Gear
Shop all TriggerTech Remington 700 triggers here.
Don’t miss out on Ultimate Reloader updates, make sure you’re subscribed!
Thanks,
Gavin Gear


































































