The Redding UltraMag is a hefty press. In this article, we’ll get it out of the box, set it up, and use it to load an Ultra Mag-class cartridge, 300 Norma Mag. And by the way, the dies are 1-inch, so there are a couple of new things here. Watch or read on!
Disclaimer
Ultimate Reloader LLC / Making with Metal Disclaimer: (by reading this article and/or watching video content you accept these terms). The content on this website (including videos, articles, ammunition reloading data, technical articles, gunsmithing and other information) is for demonstration purposes only. Do not attempt any of the processes or procedures shown or described on this website. All gunsmithing procedures should be carried out by a qualified and licensed gunsmith at their own risk. Do not attempt to repair or modify any firearms based on information on this website. Articles on this website are derived from original video content and may utilize artificial intelligence (AI) tools for initial drafting, transcript processing, and editorial refinement; no AI technology independently generates or verifies technical instructions or safety data. Ultimate Reloader, LLC and Making With Metal can not be held liable for property or personal damage due to viewers/readers of this website performing activities, procedures, techniques, or practices described in whole or part on this website. By accepting these terms, you agree that you alone are solely responsible for your own safety and property as it pertains to activities, procedures, techniques, or practices described in whole or part on this website.
About the Redding UltraMag
I’ve had my eye on the UltraMag press for quite a while, but I’d never used one, so I was really looking forward to experiencing it with you all.
This is a heavy-duty unit. Here’s what stands out:
- Massive cast iron frame
- Unique linkage design: The side links go all the way to the top of the press. The real selling point is leverage.
- Front loading: I’m interested to try loading from the front.
- Priming arms: The large rifle priming arm comes pre-installed, and a small priming arm is included too, which is super nice.
- Spent primer tube: Spent primers come down through the ram, so it should be neat and tidy. You could even direct the tube into a garbage can, which is something I’ll do sometimes.
- Cartridge overall length capacity: 4.25 inches usable
On-press priming is a convenience feature. You might want to use a dedicated priming tool, but the ability to prime on the press without extra tools is a big plus, especially if you’re loading in small quantities.
The 4.25-inch capacity will definitely handle anything we need for 300 Norma Mag. I believe the magazine internal length for 300 Norma Mag is around [VERIFY: 3.825] inches. Sometimes you can also tip the bullet up into the seating die to get a little more room.
1-Inch Dies
We’re loading 300 Norma Mag, and full-length sizing a 338 Lapua-ish case is going to be great with this press. I have a couple of extra items for it:
- 1-inch bushing: Steps the press up from 7/8-inch to 1-inch die threads
- Redding 300 Norma Mag 1-inch die set: A full-length sizer and a micrometer seater, just what I like
The new 1-inch dies are a little larger in diameter, and they look really, really great.
Mounting and Setup
I mounted the UltraMag solidly to the bench with a short Inline Fabrication UltraMount. It’s one I’d modified for my T-7, and fortunately it fit.
Next, I installed the handle: drop it into place and spin on the nut, using a 7/8-inch wrench.
Then I swapped the 7/8-14 bushing for the 1-inch bushing using a 1.5-inch wrench. That wasn’t too bad. Spin in the 1-inch bushing, and we were good to go.
Sizing 300 Norma Mag
We’ve been using the UltraMag through the break-in process for our 300 Norma Mag, and the results so far have been awesome. My first shots went in just over quarter MOA! Now we have a bunch of fired brass, so it was time to set up the full-length sizer.
I’d already lubed the cases with Imperial Sizing Wax, which does a great job. I expected the first case to take a bit more effort, but it was actually super, super smooth. Sometimes I find that the first case into a freshly cleaned die primes the inside of the die with lube, and subsequent cases are much smoother.
That is amazing leverage, and I like where the press is positioned vertically for pulling the expander ball back through. Honestly, it’s just easy. One of my pet peeves is having a press too high, at that awkward spot where there’s a bunch of force on the handle to pull the expander ball back through. I love this.
It’s very, very smooth, and I can definitely tell that enhanced, optimized leverage is what you want for big cases like 300 Norma Mag.
On-Press Priming
There are a couple of options for priming on the UltraMag:
- Prime on the downstroke: Flip the priming lever in, and you can size, deprime and reprime on the way down.
- Prime as a separate step: Place a primer in the primer cup, put the case in, and prime after the fact.
I like to prime as a separate step, because my mind just works a little better when I’m focusing on priming alone. But it’s really up to you.
What’s notable is that, for on-press priming, I think the UltraMag has the highest degree of mechanical advantage, in other words, the lowest force, and you still have feel, with a very defined stopping point. That’s awesome. You can still use other priming tools, but it’s nice to have the option on the press.
Seating Bullets
For our next round of testing, I charged five cases with 80 grains of [VERIFY: Hodgdon Retumbo] and seated Hornady 230 grain A-Tip bullets. We’ll see what kind of groups, ES and SD we get.
I swapped in the micrometer seater. I’d already done the Loctite trick to measure to the lands with a fired case and get a baseline for where we want to be, so we’re changing one variable.
With the priming lever flipped down, I tipped the bullet slightly into the die and seated it. It’s super smooth, with a very defined stopping point.
Bullet seating is my favorite part of the reloading process for precision rifle. I think it’s because you’re finishing off the cartridge, and it’s just a satisfying motion. With the UltraMag, I almost don’t have to push the lever; it could almost fall on its own. That’s how much leverage we have with this bad boy. Love it!
Conclusion
With five more 300 Norma Mag cartridges ready for testing, I’m really liking the UltraMag. It’s just a good, solid piece of cast iron gear. Redding is a great company that stands by its products, and you can tell the made-in-USA quality when you get it out of the box.
Consider this part one. We have more content coming, including 1-inch dies for 7 PRC and more on the 300 Norma Mag, which is shaping up to be a great light ELR rifle.
Get the Gear
Redding 300 Norma Mag 1-inch Z-Series Die Set
Don’t miss out on Ultimate Reloader updates, make sure you’re subscribed!
Thanks,
Gavin Gear


































































