Manual to Automated: Dillon 550 Full Upgrade Walkthrough

When you start out with a base progressive press like the Dillon BL550 from the “Get Started Reloading” kit, you get manual control over steps like priming and powder charging. While that deliberate pacing is great for new reloaders, taking the next step to fully automate your workflow can dramatically increase your output. In this comprehensive video walkthrough, we take the BL550 from a manual setup to a fully automated machine by upgrading the priming system, powder measure, and case ejection. Follow along as we break down the installation steps and see how the upgraded press performs at the bench. Check it out!

Disclaimer

Ultimate Reloader LLC / Making with Metal Disclaimer: (by reading this article and/or watching video content you accept these terms). The content on this website (including videos, articles, ammunition reloading data, technical articles, gunsmithing and other information) is for demonstration purposes only. Do not attempt any of the processes or procedures shown or described on this website. All gunsmithing procedures should be carried out by a qualified and licensed gunsmith at their own risk. Do not attempt to repair or modify any firearms based on information on this website. Ultimate Reloader, LLC and Making With Metal can not be held liable for property or personal damage due to viewers/readers of this website performing activities, procedures, techniques, or practices described in whole or part on this website. By accepting these terms, you agree that you alone are solely responsible for your own safety and property as it pertains to activities, procedures, techniques, or practices described in whole or part on this website.

Why Upgrade? Moving Beyond Manual Operations

While manual priming and powder charging allow for meticulous oversight—which is ideal when starting out—they can become a bottleneck when you want to speed up your process. Upgrading to Dillon’s automated systems removes those manual steps from your rhythm, letting you focus entirely on case insertion, bullet placement, and visual inspection while significantly boosting your rounds-per-hour output.

What’s Included in the Upgrade Kits

Taking the BL550 to the next level requires two primary upgrade paths:

  • Automatic Prime System Upgrade: Includes the blast shield, operating rod, large and small primer magazines, pickup tubes, primer bar assemblies, return spring, and an early primer warning alarm system.
  • Powder Measure Upgrade: Replaces the manual funnel setup with a full powder measure assembly (featuring small and large charge bars), operating return rod, bracket, and necessary hardware to meter and throw exact powder charges automatically on the press.
  • Case Ejection Upgrade: Includes an ejection wire, indexing pawl, and an ejection chute/acro bin setup to automatically clear finished cartridges off the shell plate and into a collection bin.

Step-by-Step Installation Walkthrough

Upgrading the press involves several key installation stages:

  1. Installing the Automatic Priming System:
    • Remove the old manual priming components using a 3/8 wrench and 5/32 hex key.
    • Install the new roll pin for the return spring using a roll pin punch and ball-peen hammer.
    • Mount the blast shield and priming assembly base onto the press frame, hook up the return spring, and attach the operating rod that rides along the ram.
    • Install the primer magazine tube and the early primer warning alarm system. Adjust the rear socket-head cap screw to ensure smooth primer arm return travel.
  2. Upgrading to the Automatic Powder Measure:
    • Remove the old manual powder funnel die from Toolhead Station 2.
    • Install the new powder measure die and insert the appropriate powder funnel into the bottom.
    • Mount the powder measure on top of the die, connect the return arm lever to the press bracket, and adjust the wing nut for proper bar return tension (leaving roughly a credit card’s width of clearance).
    • Fill the measure, dial in your target charge weight using the adjustment bolt, and cycle the press several times to ensure consistent powder dropping.
  3. Setting Up the Case Ejection System:
    • Insert the ejection wire into the mounting holes on the right side of the press frame, ensuring it sits just above the shell plate for smooth, frictionless rotation.
    • Mount the ejection chute (using the strong-mount chute or bench-mounted acro bin depending on your setup) and attach the collection bin.

Bench Performance and Progressive Reloading

With all automated components installed, dialed in, and verified, the BL550 transforms into a streamlined progressive powerhouse. Operating the press now requires only two physical actions per cycle: inserting a piece of brass and placing a bullet.

The automated powder drop and primer feed operate seamlessly together, allowing you to maintain a steady cadence while visually inspecting each charged case before seating the bullet. The result is a massive jump in efficiency and output speed compared to the manual baseline setup.

Conclusion

Upgrading the Dillon BL550 from a manual starter kit to a fully automated progressive press provides the best of both worlds: a solid, reliable foundation that grows right alongside your reloading experience. Whether you want to retain manual control over certain steps or maximize your bench efficiency, the upgrade path delivers exceptional performance and flexibility.

Get the Gear

Dillon BL550 to RL550 Upgrade Kit

Don’t miss out on Ultimate Reloader updates, make sure you’re subscribed!

Thanks,
Kyle Shields

About the author

Leave a Reply

Your email address will not be published. Required fields are marked *